A few years ago, I got a Wansview NCH-536MW IP camera. That was one of the first 720p cameras with night-vision, motion and all features you could wish for.
One problem, though: The user interface looks awfully outdated and half of the setup only works in Microsoft Internet Explorer and only if you have some Chinese OCX browser plugin installed. (Compared to Foscam, however, you can at least setup most things without that plugin. With Foscam cameras, you can't even login if you don't have their plugin installed.)
While that works, once you have everything set up, it's always a hassle to change a setting - especially as a Linux user. I need to power up a Windows VM to change anything. And I don't like that.
However, the German company Instar developed an awesome HTML5 interface which works like a charm and is cross-browser compatible. It even works from Linux. And you can setup everything without the need for any plugin.
Brothers in spirit (and hardware)
The problem is: There are various different models of IP cameras out there and while they may share the same body, they can have totally different hardware inside. (Camera bodies are re-used amongst companies to not having to spend resources on designing one.)
But luckily that's not the case with the NCH-536MW. Because the company behind it, Wansview, is also known as Shenzhen Smarteye Digital Electronics Co.. And under the SmartEye branch, they sell these cameras to OEMs. And those OEMs may use the original firmware, or, provide their customers with a customised one.
The hardware I have is sold under these product names:
- Wansview NCH-536MW
- AGASIO A522W (original UI)
- DERICAM H501W (customised UI)
- Foscam FI9820W (customised UI)
- INSTAR IN-6011HD (customised UI)
There's a HiSilicon Hi3511-compatible SoC with a 16MB Flash memory in it.
Firmware updates come in form of a
.pkg file. For the Wansview variant, the
latest one is
B12SE_V184.108.40.206.9_536mP1.pkg. The INSTAR one is named
B12SE_V220.127.116.11_536mP1_18.104.22.168.18.pkg and Foscam's latest firmware for the
SE = SmartEye/Wansview,
If you take a closer look at those files, you'll notice that they consist of 144 Bytes header data (188 Bytes in older versions) and the rest is a JFFS2 image, around 9-point-something MiB in (compressed) size.
You can get the plain JFFS2 file by running, e.g.:
dd if=B12SE_V22.214.171.124_536mP1_126.96.36.199.18.pkg bs=1 skip=144 of=root.jffs2
You can then mount it with these commands
(you probably have to use
sudo with each of them):
mknod /tmp/mtdblock0 b 31 0 modprobe mtd modprobe jffs2 modprobe mtdram total_size=32767 modprobe mtdblock dd if="root.jffs2" of=/dev/mtd0 mount -t jffs2 /tmp/mtdblock0 /mnt/jffs2
However, this isn't much use as we want to get the files onto the camera, not on our desktop PC.
Sadly, the normal firmware updater doesn't allow files from a different reseller. So we have to find another way. And there is one.
If you open up the camera, you'll notice several unpopulated connectors on the PCB. What you're looking for is the (mostly) 4-pin console port. A serial port which acts as the main input/output interface to the system. And this is it:
Only 3 pins are important to us: Rx (green), Tx (red) and the GND (white) pin. The fourth is supplying 3.3V which we don't need.
Once you've wired everything correctly and connected the serial adapter to your
computer, a new serial port should show up. Connect to it using a terminal
program, e.g. minicom or KiTTY.
The comm parameters are: 115200 8 N 1, e.g.
minicom -b 115200 -D /dev/ttyUSB0.
After you've set up everything, plug in the camera.
You should see the boot process, U-Boot first followed by the linux kernel. The first few lines look like this:
U-Boot 1.1.4 (Apr 8 2009 - 11:41:01) U-Boot code: E0500000 -> E0517540 BSS: -> E051E2BC HI_VERSION=U_BOOT_1_1_4-M08C0305B0301 @Hi3511v110_OSDrv_1_0_0_7 2009-03-18 20:44:35 RAM Configuration: Bank #0: e0000000 128 MB Flash: 16 MB In: serial Out: serial Err: serial MAC: 00-25-07-00-00-3B Hit any key to stop autoboot: 0 Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists Kernel command line: mem=72M console=ttyAMA0,115200 root=1f01 rootfstype=jffs2 mtdparts=phys_mapped_flash:2M(boot),13M(rootfs),1M(setting) PID hash table entries: 512 (order: 9, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 72MB = 72MB total Memory: 71168KB available (1461K code, 175K data, 76K init)
Notice the "Hit any key to stop autoboot" message. If you press any key at that step, you'll be dropped into the U-Boot bootloader. That's where we want to be.
help to get a list of supported commands:
hilinux # help ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol cmp - memory compare cp - memory copy crc32 - checksum calculation dhcp - invoke DHCP client to obtain IP/boot params echo - echo args to console erase - erase FLASH memory flinfo - print FLASH memory information go - start application at address 'addr' help - print online help loadb - load binary file over serial line (kermit mode) loop - infinite loop on address range md - memory display mm - memory modify (auto-incrementing) mtest - simple RAM test mw - memory write (fill) nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU saveenv - save environment variables to persistent storage setenv - set environment variables tftp - download or upload image via network using TFTP protocol version - print monitor version
Of those, we need three commands:
Setting up the TFTP connection
First, we need to setup the connection to the PC. Make sure to connect the camera via ethernet cable to your network. And you need to setup a tftp server on your PC. I used atftpd. For Windows, there's tftpd32.
Now, we need to configure the IPv4 settings. Use these commands:
setenv ipaddr 172.16.99.9 setenv netmask 255.255.0.0 setenv serverip 172.16.1.2
ipaddr is the IP address of your camera (or some other unused IP address in
serverip is the IP address of your PC (or where your TFTP
server is running). And
netmask is, of course, the netmask of your network.
The 16M flash memory is located at address 0x34000000 until 0x34ffffff and partitioned like this:
- 0x34000000 - 0x341fffff = boot area
- 0x34000000 is the U-Boot start area
- 0x34100000 is the linux kernel
- 0x34200000 - 0x34efffff = JFFS2 root filesystem
- 0x34f00000 - 0x34ffffff = settings
And yes, the JFFS2 root filesystem is the JFFS2 data from the firmware update files (see above).
Making a backup
If you check the help for the
tftp command, its syntax is like this:
tftp address filename [length]
[length] is given, it will UPLOAD a file to your TFTP server, if it
is omitted, it will DOWNLOAD a file from your TFTP server and flash that
into the memory.
So, since we know the memory layout, a complete backup of everything but the bootloader (to not risk corrupting it) is as easy as:
tftp 0x34100000 recovery.bin 0xf00000
This will upload a file named
recovery.bin with the linux kernel and JFFS2
image to your TFTP server.
If you should run into problems, you can recover by entering:
erase 0x34100000 +0xf00000 tftp 0x34100000 recovery.bin
Flashing new firmware
If you read until here, it should be clear what to do. After extracting the
JFFS2 image file from, e.g. the INSTAR firmware (see above), you just have to
put it on your TFTP server to make it accessible to the camera. Let's say you
Since we know the memory area for the JFFS2 image, we can first erase it by issuing the command:
erase 0x34200000 +0xd00000
This erases the whole JFFS2 memory area, i.e. it sets all bits to
After this is complete, you just have to flash the file from the TFTP server:
tftp 0x34200000 instar.jffs2
That's it. You can now reboot the camera into the INSTAR firmware:
(This boots from memory at address 0x3410000 - the linux kernel, which will then mount the JFFS2 image and continue booting from there.)
If you see something like this on bootup of a newly flashed firmware:
jffs2_scan_dirent_node(): Node CRC failed on node at 0x0000000c: Read 0x41c0224d, calculated 0x97e7f5c5 jffs2_scan_inode_node(): CRC failed on node at 0x00000038: Read 0x5a000025, calculated 0x1b754c4d jffs2_scan_dirent_node(): Node CRC failed on node at 0x0000007c: Read 0x53804006, calculated 0x88f20f93 jffs2_scan_inode_node(): CRC failed on node at 0x000000a8: Read 0x1a180001, calculated 0x05c7cb76 jffs2_scan_dirent_node(): Node CRC failed on node at 0x000000ec: Read 0x130c0000, calculated 0x84df6ac9 jffs2_scan_inode_node(): CRC failed on node at 0x00000118: Read 0xeb290421, calculated 0x5025ee1e jffs2_scan_dirent_node(): Node CRC failed on node at 0x0000015c: Read 0x00006680, calculated 0x061da826 jffs2_scan_inode_node(): CRC failed on node at 0x00000188: Read 0xaa620051, calculated 0x4e976925 jffs2_scan_dirent_node(): Node CRC failed on node at 0x000001cc: Read 0x91724800, calculated 0x6a08a595 jffs2_scan_inode_node(): CRC failed on node at 0x000001f8: Read 0x10481681, calculated 0xceb194da jffs2_scan_dirent_node(): Node CRC failed on node at 0x0000023c: Read 0x041c0010, calculated 0x936f78f5 jffs2_scan_inode_node(): CRC failed on node at 0x00000268: Read 0xadab3105, calculated 0x16f7db7a jffs2_scan_dirent_node(): Node CRC failed on node at 0x000002ac: Read 0x0108e480, calculated 0xc7802b02 jffs2_scan_inode_node(): CRC failed on node at 0x000002dc: Read 0x13e23050, calculated 0xb31f5628 jffs2_scan_dirent_node(): Node CRC failed on node at 0x00000320: Read 0x0005c825, calculated 0x9bdee4df jffs2_scan_inode_node(): CRC failed on node at 0x0000034c: Read 0x44643000, calculated 0xc2233f22 jffs2_scan_dirent_node(): Node CRC failed on node at 0x00000390: Read 0x0b70408d, calculated 0xd00bb938 jffs2_scan_inode_node(): CRC failed on node at 0x000003c0: Read 0x18509440, calculated 0xe7085f3d jffs2_scan_dirent_node(): Node CRC failed on node at 0x00000410: Read 0x13400000, calculated 0xac90de05 jffs2_scan_inode_node(): CRC failed on node at 0x0000043c: Read 0x6d822094, calculated 0xd6ce08ab
This means that you forgot to erase the memory area before flashing a new
firmware. Since "flashing" can only change bits from
0, it runs into
problems when there should be a
1 where there already is a
Old data: 0101 0101 New data: 1100 1100 Flash data: 0100 0100
erase command resets all bits to